LAN settings
Select this setting item from Device settings in the menu screen which appears when you select (Setup) on the HOME screen.
Wi-Fi
By selecting Wi-Fi from LAN settings, the following settings are available.
To print the LAN settings, select Print details in the LAN settings and select Yes.
Important
-
The network settings printout contains important information about your network. Handle it with care.
-
Advanced mode
Enables/disables Wi-Fi.
-
Wi-Fi setup
Selects the setup method for Wi-Fi connection.
-
Easy wireless connect
Select if you specify the settings of the access point information to the printer directly from a device (e.g. smartphone, or tablet) without operating the wireless router. Follow the on-screen instructions of the connecting device for the setup procedure.
-
Manual connect
Select when you perform settings for Wi-Fi manually using the operation panel of the printer.
-
WPS (Push button method)
Select when you perform settings for Wi-Fi using a wireless router supporting a Wi-Fi Protected Setup (WPS) push button method. Follow the on-screen instructions during setup.
-
Other connection types
-
Manual connect (adv.)
Select when you perform settings for Wi-Fi manually. You can specify multiple WEP keys.
-
WPS (PIN code method)
Select when you perform settings for Wi-Fi using a wireless router supporting a Wi-Fi Protected Setup (WPS) PIN code method. Follow the on-screen instructions during setup.
-
-
-
Show setting info
The following setting items are displayed. (Some setting items are not displayed depending on the printer settings.)
Items | Setting |
---|---|
Connection | Enabled (connected)/Enabled (disconnected)/Disabled |
Network name (SSID) | XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX (up to 32 characters) |
Frequency | 2.4 GHz/5 GHz |
Wi-Fi security | Inactive/WEP(64bit)/WEP(128bit)/WPA-PSK(TKIP)/WPA-PSK(AES)/WPA2-PSK(TKIP)/WPA2-PSK(AES) |
Signal strength (%) | XXX |
IPv4 address | XXX. XXX. XXX. XXX (12 characters) |
IPv4 subnet mask | XXX. XXX. XXX. XXX (12 characters) |
IPv4 default gateway | XXX. XXX. XXX. XXX (12 characters) |
IPv6 link-local address | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters) |
MAC address (Wi-Fi) | XXX. XXX. XXX. XXX (12 characters) |
Printer name | XXXXXXXXXXXXXXX (up to 15 characters) |
Bonjour service name | XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX (up to 52 characters) |
("XX" represents alphanumeric characters.)
-
Advanced
For details on each setting item:
Wireless Direct
By selecting Wireless Direct from LAN settings, the following settings are available.
To print the LAN settings, select Print details in the LAN settings screen and select Yes.
Important
-
The network settings printout contains important information about your network. Handle it with care.
-
Advanced mode
Enables/disables Wireless Direct.
-
Show setting info
The following setting items are displayed. (Some setting items are not displayed depending on the printer settings.)
Note
-
Select Show setting info to display a screen, allowing you to show or hide the password.
-
Items | Setting |
---|---|
Connection | Enabled (connected)/Disabled |
Network name(SSID) | DIRECT-XXXX-TR150series |
Password | XXXXXXXXXX (10 characters) |
Wi-Fi security | WPA2-PSK(AES) |
No. of devices connected now | XX/XX |
IPv4 address | XXX. XXX. XXX. XXX (12 characters) |
IPv4 subnet mask | XXX. XXX. XXX. XXX (12 characters) |
IPv4 default gateway | XXX. XXX. XXX. XXX (12 characters) |
IPv6 link-local address | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters) |
MAC address (Wi-Fi) | XXX. XXX. XXX. XXX (12 characters) |
Printer name | XXXXXXXXXXXXXXX (up to 15 characters) |
Bonjour service name | XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX (up to 52 characters) |
("XX" represents alphanumeric characters.)
-
Change network name (SSID)
Changes the identifier (SSID/the printer's name displayed on a Wi-Fi Direct compatible device) for Wireless Direct.
-
Change password
Changes the password for Wireless Direct.
-
Connection request confirmation
Selecting ON displays the confirmation screen when a Wi-Fi Direct compatible device is connecting the printer.
-
Advanced
For details on each setting item:
Advanced
-
Set printer name
Specifies the printer name. You can use up to 15 characters for the name.
Note
-
You cannot use the same printer name as that already used for other LAN connected devices.
-
You cannot use a hyphen for the initial or last character of the printer name.
-
-
TCP/IP settings
Performs IPv4 or IPv6 setting.
-
WSD setting
Setting items when you use WSD (one of the network protocols supported in Windows).
-
Enable/disable WSD
Selects whether WSD is enabled or disabled.
Note
-
When this setting is enabled, the printer icon is displayed on the Network Explorer in Windows.
-
-
Optimize inbound WSD
Selecting Enable allows you to receive the WSD printing data faster.
-
Timeout setting
Specifies the timeout length.
-
-
Bonjour settings
Setting items for LAN using Bonjour for macOS.
-
Enable/disable Bonjour
Selecting Enable allows you to use Bonjour to perform the network settings.
-
Service name
Specifies the Bonjour service name. You can use up to 48 characters for the name.
Note
-
You cannot use the same service name as that already used for other LAN connected devices.
-
-
-
LPR protocol setting
Enables/disables the LPR setting.
-
RAW protocol
Enables/disables RAW printing.
-
LLMNR
Enables/disables LLMNR (Link-Local Multicast Name Resolution). Selecting Enable allows the printer to detect printer's IP address from the printer name without a DNS server.
-
IPP settings
Selecting Enable allows you to print via the network with the IPP protocol.
-
PictBridge communication
Setting items for printing from a PictBridge (Wi-Fi) compliant device.
-
Enable/disable communication
Selecting Enable allows you to print from a PictBridge (Wi-Fi) compliant device.
-
Timeout setting
Specifies the timeout length.
-
-
Wi-Fi DRX setting
Selecting Enable allows you to activate discontinuous reception when using Wi-Fi (intermittent reception).
Note
-
Depending on your router, the intermittent reception may not be available even if Enable is selected.
-
The intermittent reception is available only when the printer is in standby mode (the LCD is automatically off).
-
-
IPsec settings
Selecting Enable allows you to specify the IPsec security.